Beta
BWBV0002775
BWBV0002775 — Protocol bij het Verdrag van 1979 betreffende grensoverschrijdende luchtverontreiniging over lange afstand inzake de beheersing van emissies van stikstofoxyden of van de grensoverschrijdende stromen van deze stikstofverbindingen
Beta. Legal information, not legal advice. LEGALDIGM is not a law firm. Check the official source for the current text.
Analyze this law with AIFor the purposes of the present Protocol,
1. "Convention" means the Convention on Long-range Transboundary Air Pollution, adopted in Geneva on 13 November 1979;
2. "EMEP" means the Co-operative Programme for Monitoring and Evaluation of the Long-range Transmission of Air Pollutants in Europe;
3. "Executive Body" means the Executive Body for the Convention constituted under article 10, paragraph 1 of the Convention;
4. "Geographical scope of EMEP" means the area defined in article 1, paragraph 4 of the Protocol to the 1979 Convention on Long-range Transboundary Air Pollution on Long-term Financing of the Co-operative Programme for Monitoring and Evaluation of the Long-range Transmission of Air Pollutants in Europe (EMEP), adopted in Geneva on 28 September 1984;
5. "Parties" means, unless the context otherwise requires, the Parties to the present Protocol;
6. "Commission" means the United Nations Economic Commission for Europe;
7. "Critical load" means a quantitative estimate of the exposure to one or more pollutants below which significant harmful effects on specified sensitive elements of the environment do not occur according to present knowledge;
8. "Major existing stationary source" means any existing stationary source the thermal input of which is at least 100 MW;
9. "Major new stationary source" means any hew stationary source the thermal input of which is at least 50 MW;
10. "Major source category" means any category of sources which emit or may emit air pollutants in the form of nitrogen oxides, including the categories described in the Technical Annex, and which contribute at least 10 per cent of the total national emissions of nitrogen oxides on an annual basis as measured or calculated in the first calendar year after the date of entry into force of the present Protocol, and every fourth year thereafter;
11. "New stationary source" means any stationary source the construction or substantial modification of which is commenced after the expiration of two years from the date of entry into force of this Protocol;
12. "New mobile source" means a motor vehicle or other mobile source which is manufactured after the expiration of two years from the date of entry into force of the present Protocol.
1. The Parties shall, as soon as possible and as a first step, take effective measures to control and/or reduce their national annual emissions of nitrogen oxides or their transboundary fluxes so that these, at the latest by 31 December 1994, do not exceed their national annual emissions of nitrogen oxides or transboundary fluxes of such emissions for the calendar year 1987 or any previous year to be specified upon signature of, or accession to, the Protocol, provided that in addition, with respect to any Party specifying such a previous year, its national average annual transboundary fluxes or national average annual emissions of nitrogen oxides for the period from 1 January 1987 to 1 January 1996 do not exceed its transboundary fluxes or national emissions for the calendar year 1987.
2. Furthermore, the Parties shall in particular, and no later than two years after the date of entry into force of the present Protocol:
(a) Apply national emissions standards to major new stationary sources and/or source categories, and to substantially modified stationary sources in major source categories, based on the best available technologies which are economically feasible, taking into consideration the Technical Annex;
(b) Apply national emission standards to new mobile sources in all major source categories based on the best available technologies which are economically feasible, taking into consideration the Technical Annex and the relevant decisions taken within the framework of the Inland Transport Committee of the Commission; and
(c) Introduce pollution control measures for major existing stationary sources, taking into consideration the Technical Annex and the characteristics of the plant, its age and its rate of utilization and the need to avoid undue operational disruption.
3. (a) The Parties shall, as a second step, commence negotiations, no later than six months after the date of entry into force of the present Protocol, on further steps to reduce national annual emissions of nitrogen oxides or transboundary fluxes of such emissions, taking into account the best available scientific and technological developments, internationally accepted critical loads and other elements resulting from the work programme undertaken under article 6.
(b) To this end, the Parties shall co-operate in order to establish: (i) Critical loads; (ii) Reductions in national annual emissions of nitrogen oxides or transboundary fluxes of such emissions as required to achieve agreed objectives based on critical loads; and (iii) Measures and a time-table commencing no later than 1 January 1996 for achieving such reductions.
4. Parties may take more stringent measures than those required by the present article.
1. The Parties shall, consistent with their national laws, regulations and practices, facilitate the exchange of technology to reduce emissions of nitrogen oxides, particularly through the promotion of:
(a) Commercial exchange of available technology;
(b) Direct industrial contacts and co-operation, including joint ventures;
(c) Exchange of information and experience; and
(d) Provision of technical assistance.
2. In promoting the activities specified in subparagraphs (a) to (d) above, the Parties shall create favourable conditions by facilitating contacts and co-operation among appropriate organizations and individuals in the private and public sectors that are capable of providing technology, design and engineering services, equipment or finance.
3. The Parties shall, no later than six months after the date of entry into force of the present Protocol, commence consideration of procedures to create more favourable conditions for the exchange of technology to reduce emissions of nitrogen oxides.
The Parties shall, as soon as possible and no later than two years after the date of entry into force of the present Protocol, make unleaded fuel sufficiently available, in particular cases as a minimum along main international transit routes, to facilitate the circulation of vehicles equipped with catalytic converters.
1. The Parties shall regularly review the present Protocol, taking into account the best available secientific substantiation and technological development.
2. The first review shall take place no later than one year after the date of entry into force of the present Protocol.
The Parties shall give high priority to research and monitoring related to the development and application of an approach based on critical loads to determine, on a scientific basis, necessary reductions in emissions of nitrogen oxides. The Parties shall, in particular, through national research programmes, in the work plan of the Executive Body and through other co-operative programmes within the framework of the Convention, seek to:
(a) Identify and quantify effects of emissions of nitrogen oxides on humans, plant and animal life, waters, soils and materials, taking into account the impact on these of nitrogen oxides from sources other than atmospheric deposition;
(b) Determine the geographical distribution of sensitive areas;
(c) Develop measurements and model calculations including harmonized methodologies for the calculation of emissions, to quantify the long-range transport of nitrogen oxides and related pollutants;
(d) Improve estimates of the performance and costs of technologies for control of emissions of nitrogen oxides and record the development of improved and new technologies; and
(e) Develop, in the context of an approach based on critical loads, methods to integrate scientific, technical and economic data in order to determine appropriate control strategies.
The Parties shall develop without undue delay national programmes, policies and strategies to implement the obligations under the present Protocol that shall serve as a means of controlling and reducing emissions of nitrogen oxides or their transboundary fluxes.
1. The Parties shall exchange information by notifying the Executive Body of the national programmes, policies and strategies that they develop in accordance with article 7 and by reporting to it annually on progress achieved under, and any changes to, those programmes, policies and strategies, and in particular on:
(a) The levels of national annual emissions of nitrogen oxides and the basis upon which they have been calculated;
(b) Progress in applying national emission standards required under article 2, subparagraphs 2 (a) and 2 (b), and the national emission standards applied or to be applied, and the sources and/or source categories concerned;
(c) Progress in introducing the pollution control measures required under article 2, subparagraph 2 (c), the sources concerned and the measures introduced or to be introduced;
(d) Progress in making unleaded fuel available;
(e) Measures taken to facilitate the exchange of technology; and
(f) Progress in establishing critical loads.
2. Such information shall, as far as possible, be submitted in accordance with a uniform reporting framework.
EMEP shall, utilizing appropriate models and in good time before the annual meetings of the Executive Body, provide to the Executive Body calculations of nitrogen budgets and also of transboundary fluxes and deposition of nitrogen oxides within the geographical scope of EMEP. In areas outside the geographical scope of EMEP, models appropriate to the particular circumstances of Parties to the Convention therein shall be used.
The Technical Annex to the present Protocol is recommendatory in character. It shall form an integral part of the Protocol.
1. Any Party may propose amendments to the present Protocol.
2. Proposed amendments shall be submitted in writing to the Executive Secretary of the Commission who shall communicate them to all Parties. The Executive Body shall discuss the proposed amendments at its next annual meeting provided that these proposals have been circulated by the Executive Secretary to the Parties at least ninety days in advance.
3. Amendments to the Protocol, other than amendments to its Technical Annex, shall be adopted by consensus of the Parties present at a meeting of the Executive Body, and shall enter into force for the Parties which have accepted them on the ninetieth day after the date on which two-thirds of the Parties have deposited their instruments of acceptance thereof. Amendments shall enter into force for any Party which has accepted them after two-thirds of the Parties have deposited their instruments of acceptance of the amendment, on the ninetieth day after the date on which that Party deposited its instrument of acceptance of the amendments.
4. Amendments to the Technical Annex shall be adopted by consensus of the Parties present at a meeting of the Executive Body and shall become effective thirty days after the date on which they have been communicated in accordance with paragraph 5 below.
5. Amendments under paragraph 3 and 4 above shall, as soon as possible after their adoption, be communicated by the Executive Secretary to all Parties.
If a dispute arises between two or more Parties as to the interpretation or application of the present Protocol, they shall seek a solution by negotiation or by any other method of dispute settlement acceptable to the parties to the dispute.
1. The present Protocol shall be open for signature at Sofia from 1 November 1988 until 4 November 1988 inclusive, then at the Headquarters of the United Nations in New York until 5 May 1989, by the member States of the Commission as well as States having consultative status with the Commission, pursuant to paragraph 8 of Economic and Social Council resolution 36 (IV) of 28 March 1947, and by regional economic integration organizations, constituted by sovereign States members of the Commission, which have competence in respect of the negotiation, conclusion and application of international agreements in matters covered by the Protocol, provided that the States and organizations concerned are Parties to the Convention.
2. In matters within their competence, such regional economic integration organizations shall, on their own behalf, exercise the rights and fulfil the responsibilities which the present Protocol attributes to their member States. In such cases, the member States of these organizations shall not be entitled to exercise such rights individually.
1. The present Protocol shall be subject to ratification, acceptance or approval by Signatories.
2. The present Protocol shall be open for accession as from 6 May 1989 by the States and organizations referred to in article 13, paragraph 1.
3. A State or organization which accedes to the present Protocol after 31 December 1993 may implement articles 2 and 4 no later than 31 December 1995.
4. The instruments of ratification, acceptance, approval or accession shall be deposited with the Secretary-General of the United Nations, who will perform the functions of depositary.
1. The present Protocol shall enter into force on the ninetieth day following the date on which the sixteenth instrument of ratification, acceptance, approval or accession has been deposited.
2. For each State and organization referred to in article 13, paragraph 1, which ratifies, accepts or approves the present Protocol or accedes thereto after the deposit of the sixteenth instrument of ratification, acceptance, approval, or accession, the Protocol shall enter into force on the ninetieth day following the date of deposit by such Party of its instrument or ratification, acceptance, approval, or accession.
At any time after five years from the date on which the present Protocol has come into force with respect to a Party, that Party may withdraw from it by giving written notification to the depositary. Any such withdrawal shall take effect on the ninetieth day following the date of its receipt by the depositary, or on such later date as may be specified in the notification of the withdrawal.
The original of the present Protocol, of which the English, French and Russian texts are equally authentic, shall be deposited with the Secretary-General of the United Nations.
I CONTROL TECHNOLOGIES FOR NOx EMISSIONS FROM STATIONARY SOURCES – GENERAL OPTIONS FOR REDUCING NOx EMISSIONS FROM COMBUSTION – Other combustion technologies
Stationary combustion turbines can also be integrated into existing conventional power plants (known as topping). The overall efficiency can increase by 5% tot 6%, but achievable NOx reduction will depend on site and fuel specific conditions. Gas turbines and gas engines are widely applied in cogeneration applications. Typically some 30% energy saving can be attained. Both have made significant progress in reducing NOx emissions through new concepts in combustion and system technology. However, major alterations to the existing boiler system become necessary.
FBC is a combustion technology for burning hard coal and brown coal but it can burn other solid fuels such as petroleum coke and lowgrade fuels such as waste, peat and wood. In addition, emissions can be reduced by integrated combustion control in the system. A newer concept of FBC is pressurized fluidized bed combustion (PFBC) presently being commercialized for the generation of electricity and heat. The total installed capacity of FBC has approached approximately 30.000 MWth (250 to 350 plants), including 8,000 MWth in the capacity range of > 50 MWth.
The IGCC process incorporates coal gasification and combined cycle power generation, in a gas and steam turbine. The gasified coal is burned in the combustion chamber of the gas turbine. The technology also exists for heavy oil residue and bitumen emulsion. The installed capacity is presently about 1,000 MWel (5 plants).
Combined cycle gas power stations using advanced gas turbines with an energy efficiency of 48%–52% and with reduced NOx emissions are currently being planned.
I CONTROL TECHNOLOGIES FOR NOx EMISSIONS FROM STATIONARY SOURCES – GENERAL OPTIONS FOR REDUCING NOx EMISSIONS FROM COMBUSTION – Process and combustion modifications
These are measures applied during combustion to reduce the formation of NOx. They include the control of combustion air ratio, flame temperature, fuel to air ratio, etc. The following combustion techniques, either singly or in combination, are available for new and existing installations. They are widely implemented in the power plant sector and in some areas of the industrial sector:
a) Low excess air combustion (LEA);1)Typical retrofit measures, with limited efficiency and applicability.
b) Reduced air preheat (RAP);1)Typical retrofit measures, with limited efficiency and applicability.
c) Burner-out-of-service (BOOS);1)Typical retrofit measures, with limited efficiency and applicability.
d) Biased-burner-firing (BBF);1)Typical retrofit measures, with limited efficiency and applicability.
e) Low NOx burners (LNB);1)Typical retrofit measures, with limited efficiency and applicability. and2)State-of-the-art in new plants.
f) Flue gas recirculation (FGR);3)Implemented in single large commercial plants; operational experience still limited.
g) Over fire air combustion (OFA);1)Typical retrofit measures, with limited efficiency and applicability. and2)State-of-the-art in new plants.
h) In-furnace-NOx-reduction reburning (IFNR);3)Implemented in single large commercial plants; operational experience still limited.
i) Water/steam injection and lean/premixed combination.4)For combustion turbines.
The emission levels due to the application of these techniques are summarized in table 1 (based mainly on experience in power plants).
Combustion modifications have been under continuous development and optimization. In-furnace-NOx-reduction is being tested in some large-scale demonstration plants, whereas basic combustion modifications are incorporated mainly into boiler and burner design. For example, modern furnace designs incorporate OFA parts, and gas/oil burners are equipped for flue gas recirculation. The latest generation of LNBs combines both air-staging and fuel-staging. A remarkable increase in full-scale retrofit of combustion modifications in ECE member countries has been recorded in the last years. By 1992 a total of about 150,000 MW was installed.
I CONTROL TECHNOLOGIES FOR NOx EMISSIONS FROM STATIONARY SOURCES – GENERAL OPTIONS FOR REDUCING NOx EMISSIONS FROM COMBUSTION – Flue gas treatment processes
Flue gas treatment processes aim at removing already formed NOx and are also referred to as secondary measures. Wherever possible it is usual to apply primary measures as a first stage of NOx reduction before applying flue gas treatment processes. The state-of-the-art flue gas treatment processes are all based on the removal of NOx by dry chemical processes.
They are the following:
a) Selective Catalytic Reduction (SCR);
b) Selective Non-catalytic Reduction (SNCR);
c) Combined NOx/SOx removal processes: (i) Activated Carbon Process (AC); (ii) Combined catalytic NOx/SOx removal.
The emission levels for SCR and SNCR are summarized in table 1. Data are based on the practical experience gathered from a large number of implemented plants. By 1991 in the European part of the ECE about 130 SCR plants corresponding to 50,000 MWel, 12 SNCR installations (2,000 MWel), 1 AC plant (250 MWel and 2 combined catalytic processes (400 MWel) were erected. The NOx removal efficiency of AC and combined catalytic processes are similar to SCR.
Table 1 also summarizes the costs of applying the NOx abatement technologies.
I CONTROL TECHNOLOGIES FOR NOx EMISSIONS FROM STATIONARY SOURCES – CONTROL TECHNIQUES FOR OTHER SECTORS
Unlike most combustion processes, the application of combustion and/or process modifications in the industrial sector has many process specific limitations. In cement kilns or glass melting furnaces, for example, certain high temperatures are necessary to ensure the product quality. Typical combustion modifications being used are staged combustion/ low NOx burners, flue gas recirculation and process optimization (e.g. precalcination in cement kilns).
Some examples are given in table 1.
I CONTROL TECHNOLOGIES FOR NOx EMISSIONS FROM STATIONARY SOURCES – SIDE-EFFECTS/BY-PRODUCTS
The following side-effects will not prevent the implementation of any technology or method, but should be considered when several NOx abatement options are possible. However, in general, these side-effects can be limited by proper design and operation:
a) Combustion modifications: Possible decrease in overall efficiency; Increased CO formation and hydrocarbon emissions; Corrosion due to reducing atmosphere; Possible N2O formation in FBC systems; Possible increase of carbon fly ash;
b) SCR: NH3 in the fly ash; Formation of ammonium salts on downstream facilities; Deactivation of catalyst; Increased conversion of SO2 to SO3;
c) SNCR: NH3 in the fly ash; Formation of ammonium salts on downstream facilities; Possible formation of N20.
In terms of by-products, deactivated catalysts from the SCR process are the only relevant products. Due to the classification as waste, a simple disposal is not possible, however recycling options exist.
The reagent production of ammonia and urea for flue gas treatment processes involves a number of separate steps which require energy and reactants. The storage systems for ammonia are subject to the relevant safety legislation and such systems are designed to operate as totally closed systems, with a resultant minimum of ammonia emissions. The use of NH3 is, however, not jeopardized even when taking into account the indirect emissions related to the production and transportation of NH3.
I CONTROL TECHNOLOGIES FOR NOx EMISSIONS FROM STATIONARY SOURCES – MONITORING AND REPORTING
The measures taken to carry out national strategies and policies for the abatement of air pollution include legislation and regulatory provisions, economic incentives and disincentives, as well as technological requirements (best available technology).
In general emission limiting standards may be set per emission source according to plant size, operating mode, combustion technology, fuel type and whether it is a new or existing plant. An alternative approach also used is to set a target for the reduction of total NOx emissions from a group of existing sources and to allow the Parties to choose where to take action to reach this target (bubble concept).
The limiting of the NOx emissions to the levels set out in the national framework legislation has to be controlled by a permanent monitoring and reporting system and reported to the supervising authorities.
Several monitoring systems, using both continuous and discontinuous measurement methods, are available. However quality requirements vary among Parties. Measurements are to be carried out by qualified instititutes and approved measuring/monitoring systems. To this end a certification system would provide the best assurance.
In the framework of modern automated monitoring systems and process control equipment, reporting creates no problems. The collection of data for further use is a state-of-the-art technique. However, data to be reported to competent authorities differ from Party to Party. To obtain better comparability, data sets and prescribing regulations should be harmonized. Harmonization is also desirable for quality assurance of measuring/monitoring systems. This should be taken into account when comparing data from different Parties.
To avoid discrepancies and inconsistencies, key issues and parameters including the following, must be well-defined:
Definition of the standards expressed as ppmv, mg/m3, g/GJ, kg/h or hg/t of products. Most of these units need to be calculated and need specification in terms of gas temperature, humidity, pressure, oxygen content or heat input value;
Definition of time over which standards may be averaged, expressed as hours, months or a year;
Definition of failure times and corresponding emergency regulations regarding bypass of monitoring systems or shut-down of the installation;
Definition of methods for backfilling or data missed or lost as a result of equipment failure;
Definition of the parameter set to be measured. Depending on the type of industrial process, the necessary information may differ. This also involves the location of the measurement point within the system.
Quality control of measurements must be ensured.
II CONTROL TECHNOLOGIES FOR NOx EMISSIONS FROM MOBILE SOURCES MAJOR NOx EMITTERS FROM MOBILE SOURCES
Primary mobile sources of anthropogenic NOx emissions include:
Road vehicles:
Petrol-fuelled and diesel-fuelled passenger cars;
Light commercial vehicles;
Heavy-duty vehicles (HDV);
Motor cycles and mopeds;
Tractors (agricultural and forestry).
Non-road engine applications:
Agricultural, mobile industrial and construction machinery.
Other mobile sources:
Rail transport;
Ships and other marine craft;
Aircraft.
Road transport is a major source of anthropogenic NOx emission in many ECE countries, contributing up to two thirds of the total national emissions. Current petrol-fuelled vehicles contribute up to two thirds of total national road NOx emissions. In a few cases, however, the NOx emissions from HDV traffic will exceed the decreasing emissions from passenger cars.
Many countries have enacted regulations that limit the emission of pollutants from road vehicles. For non-road applications, emission standards including NOx have been enacted by some ECE countries and are under preparation in the ECE itself. NOx emissions from these other sources may be substantial.
Until other data become available this annex concentrates on road vehicles only.
II CONTROL TECHNOLOGIES FOR NOx EMISSIONS FROM MOBILE SOURCES MAJOR NOx EMITTERS FROM MOBILE SOURCES – GENERAL ASPECTS OF CONTROL TECHNOLOGY FOR NOx EMISSIONS FROM ON-ROAD VEHICLES
The road vehicles considered in this annex are passenger cars, light commercial vehicles, motor cycles, mopeds and heavy-duty vehicles.
This annex deals with both new and in-use vehicles, with the attention primarily focused on NOx emission control for new vehicle types.
Cost figures for the various technologies given are expected production costs rather than retail prices.
It is important to ensure that new-vehicle emission standards are maintained in service. This can be done through inspection and maintenance programmes, ensuring conformity of production, full useful-life durability, warranty of emission-control components, and recall of defective vehicles.
Fiscal incentives can encourage the accelerated introduction of desirable technology. Retrofit is of limited benefit for NOx reduction, and may be difficult to apply to more than a small percentage of the vehicle fleet.
Technologies that incorporate catalytic converters with sparkignited petrol engines require the use of unleaded fuel, which should be made generally available. The use of after-treatment technologies in diesel engines like oxidation catalysts or particulate traps requires the use of low-sulphur fuels (maximum 0,05% S content).
The management of urban and loog-distance traffic, though not elaborated in this annex, is important as an efficient additional approach to reducing emissions including NOx. Measures to reduce NOx emission and other air pollutants may include enforcement of speed limits and efficient traffic management. Key measures for traffic management aim at changing the modal split of public and long-range transport especially in sensitive areas like cities or the Alps by transferring transport from road to rail through tactical, structural, financial and restrictive elements and also by optimizing the logistics of the delivery systems. They will also be beneficial for other harmful effects of traffic expansion such as noise, congestion, etc.
A variety of technologies and design options are available making simultaneous control of different pollutants possible. For some applications reverse effects have been experienced when reducing NOx emissions (e.g. non-catalyst petrol or diesel engines). This may change with the employment of new technologies (e.g. after-treatment cleaning devices and electronics). Reformulated diesel fuel and fuel containing post-combustion NOx reducing additives may also have a role in a strategy to combat diesel vehicle NOx.
II CONTROL TECHNOLOGIES FOR NOx EMISSIONS FROM MOBILE SOURCES MAJOR NOx EMITTERS FROM MOBILE SOURCES – CONTROL TECHNOLOGIES FOR NOx EMISSIONS FROM ROAD VEHICLES – Petrol- and diesel-fuelled passenger cars and light commercial vehicles
The main technologies for controlling NOx emissions are listed in table 2.
The basis for comparison in table 2 is technology option B, representing non-catalytic technology designed in response to the requirements of the United States for 1973/74 or of ECE Regulation 15-041)Replaced by Regulation No. 83. pursuant to the 1958 Agreement concerning the Adoption of Uniform Conditions of Approval and Reciprocal Recognition of Approval for Motor Vehicle Equipment and Parts. The table also presents typical emission levels for open- and closed-loop catalytic control as well as their cost.
The ‘‘uncontrolled’’ level (A) in table 2 refers to the 1970 situation in the ECE region, but may still prevail in certain areas.
The emission level in table 2 reflects emissions measured with standard test procedures. Emissions from vehicles on the road may differ because of the effect of, inter alia, ambient temperature, operating conditions (especially at higher speed), fuel properties, and maintenance. However, the reduction potential indicated in table 2 is considered representative of reductions achievable in use.
The most efficient currently available technology for NOx reduction is option E. This technology achieves large reductions of NOx, volatile organic compounds (VOC), and CO emissions.
In response to regulatory programmes for further NOx emission reductions (e.g. low-emission vehicles in California), advanced closedloop three-way catalyst systems are being developed (option F). These improvements will focus on engine management, very precise control of air-fuel ratio, heavier catalysts loading, on-board diagnostic systems (OBD) and other advanced control measures.
II CONTROL TECHNOLOGIES FOR NOx EMISSIONS FROM MOBILE SOURCES MAJOR NOx EMITTERS FROM MOBILE SOURCES – CONTROL TECHNOLOGIES FOR NOx EMISSIONS FROM ROAD VEHICLES – Motor cycles and mopeds
Although actual NOx emissions of motor cycles and mopeds are very low (e.g. with two-stroke engines), their NOx emissions should be considered. While VOC emissions of the vehicles are going to be limited by many Parties to the Convention, their NOx emissions may increase (e.g. with four-stroke engines). Generally the same technology options as described for petrol-fuelled passenger cars are applicable. In Austria and Switzerland strict NOx emission standards are already implemented.
II CONTROL TECHNOLOGIES FOR NOx EMISSIONS FROM MOBILE SOURCES MAJOR NOx EMITTERS FROM MOBILE SOURCES – CONTROL TECHNOLOGIES FOR NOx EMISSIONS FROM ROAD VEHICLES – Heavy-duty diesel-fuelled vehicles
In table 3 three technology options are summarized. The baseline engine configuration is the turbocharged diesel engine. The trend is towards turbocharged engines with intercooling, advanced fuel injection systems and electronic control. This trend may have the potential to improve baseline fuel consumption performance. Comparative etimates of fuel consumption are not included.
II CONTROL TECHNOLOGIES FOR NOx EMISSIONS FROM MOBILE SOURCES MAJOR NOx EMITTERS FROM MOBILE SOURCES – CONTROL TECHNIQUES FOR IN-USE VEHICLES – Full useful life, recall and warranties
To promote durable emission-control systems, consideration should be given to emission standards that may not be exceeded for the ‘‘full useful life’’ of the vehicle. Surveillance programmes are needed to enforce this requirement. Under such programmes, manufacturers are responsible for recalling vehicles that fail to meet the required standards. To ensure that the owner has no production-related problems, manufacturers should provide warranties for emission-control components.
There should not be any devices to reduce the efficiency or switch off the emission control systems during any operating conditions except conditions which are indispensable for trouble-free running (e.g. cold start).
II CONTROL TECHNOLOGIES FOR NOx EMISSIONS FROM MOBILE SOURCES MAJOR NOx EMITTERS FROM MOBILE SOURCES – CONTROL TECHNIQUES FOR IN-USE VEHICLES – Inspection and maintenance
The inspection and maintenance programme has an important secondary function. It may encourage regular maintenance and discourage vehicle owners from tampering with or disabling the emission controls, both through direct enforcement and public information. Inspection should verify that emission controls are in their original working order. It should also ensure that emission control systems have not been removed.
Improved monitoring of emission control performance can be achieved by on-board diagnostic systems (OBD) which monitor the functioning of emission control components, store fault codes for futher interrogation and call the attention of the driver to ensure the repair in case of malfunction.
Inspection and maintenance programmes can be beneficial for all types of control technology by ensuring that new-vehicle emission levels are maintained. For catalyst-controlled vehicles it is essential to ensure that the new-vehicle specifications and settings are maintained to avoid deterioration of all major pollutants, including NOx.
Table 1
Source category (i): Public power, cogeneration and district heating
Energy source
Uncontrolled Emissions
Process and Combustion Modifications
Flue Gas Treatment:
(a) Non-catalytic
(b) Catalytic (after primary measures)
mg/m31) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
g/GJ1) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
mg/m31) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
g/GJ1) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
ECU/kWel2) Total investments 1 ECU = 2 DM.
mg/m3 1)
g/GJ1) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
ECU/kWel2) Total investments 1 ECU = 2 DM.
mg/m31) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
g/GJ1) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
ECU/kWel2) Total investments 1 ECU = 2 DM.
Boilers:
- Coal, WBB4) At 5% O 2 .
1500-2 200
530-770
1 000-1 800
350-630
3-25
no data
no data
<200
<70
50-100 (125-200)12) Tail gas SCR configuration as opposed to high dust.
- Coal, DBBS)
800-1500
280-530
300-850
100-300
3-25
200-400
70-140
9-11
<200
<70
50-100 (115-200)12) Tail gas SCR configuration as opposed to high dust.
- Brown coal5) At 6% O2.
450-750
189-315
190-300
80-126
30-40
<200
<84
<200
<85
80-100
- Heavy oil6) At 3% O2.
700-1 400
140-400
150-500
40-140
up to 20
175-250
50-70
6-8
< 150
<40
50-70
- Light oil6) At 3% O2.
350-1 200
100-332
100-350
30-100
up to 20
no data
6-8
<150
<40
50-70
- BE14) Bitumen emulsion.
800
no data
no data
no data
no data
- Natural gas6) At 3% O2.
150-600
40-170
50-200
15-60
3-20
no data
5-7
<100
<30
FBC
200-700
180-400
1 400-1 6007) Incl. costs for boiler.
<130
no data
PFBC
150-200
50-70
11007) Incl. costs for boiler.
60
<140
<50
IGCC13) At 15% O2.
Gas turbines + CCGT13) At 15% O2.18)With supplementary firing; approximate additional thermal NOx: 0–20 g/GJ.
<600
<100
Investment
Cost:
no data
– natural gas
165-310
140-270
30-150
26-130
Dry : 50-100
ECU/kWel
NA
20
17
– diesel oil
235-430
200-370
50-200
45-175
Wet: 10-50
ECU/kWel
NA
120-180
70
IC Engines4) At 5% O 2 .
(natural gas < 1 MWel)
4 800-6 300
1 500-2 000
320 -640
100-200
Source category (ii): Commercial, institutional and residential combustion plants
Energy source
Uncontrolled Emissions
Process and Combustion Modifications
Flue Gas Treatment:
(a) Non- catalytic
(b) Catalytic (after primary measures)
mg/m31) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
g/GJ1) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
mg/m31) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
g/GJ1) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
ECU/kWel2) Total investments 1 ECU = 2 DM.
mg/m31) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
g/GJ1) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
ECU/kWel2) Total investments 1 ECU = 2 DM.
mg/m31) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
g/GJ1) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
ECU/kWel2) Total investments 1 ECU = 2 DM.
Coal
110-500
40-175
Brown coal
70-400
30-160
Light oil
180-440
50-120
130-250
35-70
Gas
140-290
40-80
60-150
16-40
2-10
Wood15) Untreated wood only.
85-200
50-120
70-140
40-80
Source category (iii): Industrial combustion plants and processes with combustion
Energy source
Uncontrolled Emissions
Process Modifications
Flue Gas Treatment:
(a) Non-catalytic
(b) Catalytic (after primary measures)
mg/m31) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
g/GJ1) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
mg/m31) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
g/GJ1) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
ECU/kWel2) Total investments 1 ECU = 2 DM.
mg/m31) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
g/GJ1) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
ECU/kWel2) Total investments 1 ECU = 2 DM.
mg/m31) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
g/GJ1) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
ECU/kWel2) Total investments 1 ECU = 2 DM.
Industrial combustion plants:
- Goal PF8) At 7% O2.
600-2 200
200-770
up to 700
up to
245
- Coal,
grates3) Reduction generally achieved in combination with primary measures. Reduction efficiency between 80 and 95%.
150-600
50-200
up to 500
up to
175
- Brown
coal
200-800
80-340
- Heavy
Oil6) At 3% O2.
400-1 000
110-280
up to 650
up to
180
- Light
0iI6) At 3% O2.
150-400
40-110
up to 250
up to
70
- Natural
gas6) At 3% O2.
100-300
30-80
up to 150
up to
42
2-10
Gas turbines + CCG13) At 15% O2.18)With supplementary firing; approximate additional thermal NOx: 0–20 g/GJ.
Investment
Cost:
- natural gas
165-310
140-270
30-150
26-130
Dry: 50-100
ECU/kWel
N/A
20
17
- diesel oil
235-430
200-370
50-200
45-175
Wet: 10-50
ECU/kWel
N/A
120-180
70
FBC8) At 7% O2.
100-700
100-600
Energy source
Uncontrolled Emissions
Process Modifications
Flue Gas Treatment:
(a) Non-catalytic
(b) Catalytic (after primary measures)
mg/m31) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
g/GJ1) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
mg/m31) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
g/GJ1) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
ECU/kWel2) Total investments 1 ECU = 2 DM.
mg/m31) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
g/GJ1) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
ECU/kWel2) Total investments 1 ECU = 2 DM.
mg/m31) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
g/GJ1) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
ECU/kWel2) Total investments 1 ECU = 2 DM.
IC Engines (natural gas) < IMWel4) At 5% O 2 .
4 800-6 300
1 500-2 000
320-640
100-200
Industrial
processes:
- Calcination Glass:
1 000-2 000
500-800
- Plate glass
6 kg/t
500-2 000
<500
- Containers
2.5 kg/t
- Fibreglass
0.5 kg/t
- Industrial Metals:
4.2 kg/t
- Sintering
300-50016) Heat recovery and gass recirculation.
1,5 kg/t
<500
- Coke ovens
1000
1 kg/t
- Baked
carbon fuels
<3 000
Electric arc furnaces
50-200
Paper and pulp:
- Black liquor
17017) For dry substance < 75%.
(50-80 g/GJ)
(20-40 g/GJ)
60
13-20
Source category (iv): Non-combustion processes
Energy source
Uncontrolled Emissions
Process Modifications
Flue Gas Treatment:
(a) Non- catalytic
(b) Catalytic (after primary measures)
mg/m31) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
kg/t9) Emissions from industrial processes are generally expressed as kg/t of product.
mg/m31) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
kg/t9) Emissions from industrial processes are generally expressed as kg/t of product.
ECU/t2) Total investments 1 ECU = 2 DM.
mg/m31) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
kg/t
ECU/kWeI2) Total investments 1 ECU = 2 DM.
mg/m31) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
kg/t9) Emissions from industrial processes are generally expressed as kg/t of product.
ECU/kWeI2) Total investments 1 ECU = 2 DM.
Nitric acid:
- Low
pressure (1-2.2 bar)
5 000
16.5
- Medium
pressure (2.3-8 bar)
approx. 1000
3.3
- High
pressure (8-15 bar)
<380
< 1.25
0.01-0.8
- HOKO
(-50 bar)
<380
< 1.25
Pickling:
- Brass
2510) g/m2 surface area.
- Stainless steel
0.3
- Carbon steel
0.1
Source category (v): Extraction, processing and distribution of fossil fuels
Energy source
Uncontrolled Emissions
Process and Combustion Modifications
Flue Gas Treatment:
(a) Non-catalytic
(b) Catalytic (after primary measures)
mg/m31) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
g/GJ1) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
mg/m31) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
g/GJ1) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
ECU/kWd2) Total investments 1 ECU = 2 DM.
mg/m31) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
g/GJ1) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
ECU/kWcl2) Total investments 1 ECU = 2 DM.
mg/m31) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
g/GJ1) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
ECU/kWcl2) Total investments 1 ECU = 2 DM.>
Refineries5) At 6% O2.
- 1000
100-700
Source category (VI): Waste treatment and disposal
Energy
Uncontrolled Emissions
Process and Combustion Modifications
Flue Gas Treatment:
(a) Non- catalytic
(b) Catalytic (after primary measures)
mg/m31) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
g/GJ1) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
mg/m31) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
g/GJ1) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
ECU/kWel2) Total investments 1 ECU = 2 DM.
mg/m31) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
g/GJ1) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
ECU/kWel2) Total investments 1 ECU = 2 DM.
mg/m31) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
g/GJ1) Emissions in mg/m3 NO2 (STP dry) resp. g/GJ thermal input. Conversion factors (mg/m3 to g/GJ) for NOX emission from coal (hard coal): 0.35, coal (lignite): 0.42, oil/gas: 0.277, peat: 0.5, wood + bark: 0.588 [1 g/GJ = 3.6 mg/kWh].
ECU/kWel2) Total investments 1 ECU = 2 DM.
Incineration11) At 11% O2.
250-500
200-400
<100
Table 2
Emission control technologies for petrol- and diesel-fuelled passenger cars and light commercial vehicles
Technology option
NOx emission level (%)
Estimated additional production cost1)Per vehicle, relative to technology option B. NOx) requirements may have an effect on fuel prices and refinery production costs, but this is not included in the estimated additional production cost. (US$)
Petrol-fuelled
A. Uncontrolled situation
100
–
B. Engine modifications (engine design, carburation and ignition systems, air injection)
70
2) Costs for engine modifications from options A tot B are estamited at US$ 40–100.
C. Open-loop catalyst
50
150–200
D. Closed-loop three-way catalyst
25
250–4503)Under technology options D, E and F, CO and VOC emissions are also substantially reduced, in addition to NOx reductions. Technology options B and C result also in CO and VOC control.
E. Advanced closed-loop three-way catalyst
10
350–6003)Under technology options D, E and F, CO and VOC emissions are also substantially reduced, in addition to NOx reductions. Technology options B and C result also in CO and VOC control.
F. Californian low-emission vehicles (advanced option E)
6
> 7003)Under technology options D, E and F, CO and VOC emissions are also substantially reduced, in addition to NOx reductions. Technology options B and C result also in CO and VOC control.
Diesel-fuelled
G. Conventional indirect injection diesel engine
40
H. Indirect injection engine with secondary injection, high injection pressures electronically controlled
30
1 000–1 2004)Fuel consumption is reduced as compared to option G, while particulate emissions of technology option G are considerably higher.
I. Direct injection engine with turbocharging
50
1 000–1 2004)Fuel consumption is reduced as compared to option G, while particulate emissions of technology option G are considerably higher.
Note: Options C, D, E, F require the use of unleaded petrol; options H and I require the use of low-sulphur diesel fuel.
Table 3
Heavy-duty vehicle technologies, emission performance and costs
Technology option
NOx emission level (%)
Expected additional production cost1)Per vehicle, and depending on engine size relative to baseline technology A. NOx) requirements may have an effect on fuel prices and refinery production costs, but this is not included in the estimated additional production cost. (US$)
A. Turbocharged diesel engine (EURO I)
100
0
B. Turbocharged diesel engine with intercooling (EURO II)
85
1 500–3 000
C. Turbocharged diesel engine with intercooling, high pressure fuel injection, electronically controlled fuel pump, combustion chamber and port optimalization, exhaust gas recirculation (EGR)
50–60
3 000–6 000
D. Shift to spark ignition engine with three-way-catalytic converter working on LPG, CNG or oxygenated fuels
10–30
up to 10 000
Note: Option C requires the use of low-sulphur diesel fuel.
