LEGALDIGMLEGALDIGM
    ← Nederland
    Beta
    BWBV0003251

    BWBV0003251 — Internationaal Verdrag van Torremolinos voor de beveiliging van vissersvaartuigen, 1977

    Beta. Legal information, not legal advice. LEGALDIGM is not a law firm. Check the official source for the current text.

    Analyze this law with AI
    The Parties shall give effect to the provisions of the Convention and the Annex thereto, which shall constitute an integral part of the Convention. Unless expressly provided otherwise, a reference to the Convention constitutes at the same time a reference to the Annex. For the purpose of the Convention, unless expressly provided otherwise: (a) “Party” means a State for which the Convention has entered into force. (b) “Fishing vessel” or “vessel” means any vessel used commercially for catching fish, whales, seals, walrus or other living resources of the sea. (c) “Organization” means the Inter-Governmental Maritime Consultative Organization. (d) “Secretary-General” means the Secretary-General of the Organization. (e) “Administration” means the Government of the State whose flag vessel is entitled to fly. The Convention shall apply to sea-going fishing vessels entitled to fly the flag of a State which is a Party. (1). Subject to the provisions of paragraph (2), a certificate issued under the authority of a Party in accordance with the provisions of the Convention shall be accepted by the other Parties and regarded for all purposes covered by the Convention as having the same validity as a certificate issued by them. (2). Every vessel holding a certificate issued under Regulation 7 or 8 is subject, in the ports of other Parties, to control by officers duly authorized by such Parties in so far as this control is directed towards verifying that there is on board a valid certificate. Such certificate shall be accepted unless there are clear grounds for believing that the condition of the vessel or its equipment does not correspond substantially with the particulars of that certificate. In that case, or if there is not a valid certificate, the officer carrying out the control shall forthwith inform the Consul or, in his absence, the diplomatic representative of the Party whose flag the vessel is entitled to fly, of all the circumstances for which corrective action by that Party would be deemed necessary and the facts shall be reported to the Organization. The officer carrying out the control shall take such steps as will ensure that the vessel shall not sail until it can proceed to sea without danger to the vessel or persons on board. (1). A vessel which is not subject to the provisions of the Convention or which is not required to hold a certificate in accordance with the provisions of the Convention at the time of its departure on any voyage shall not become subject to such provisions on account of any deviation from its intended voyage due to stress of weather or any other cause of force majeure. (2). Persons who are on board of a vessel by reason of force majeure or in consequence of the obligation to carry shipwrecked or other persons shall not be taken into account for the purpose of ascertaining the application to the vessel of any provisions of the Convention. (1). The Parties shall communicate to the Organization: (a) the text of laws, orders, decrees, regulations and other instruments which have been promulgated on the various matters within the scope of the Convention; (b) a list of non-governmental agencies which are authorized to act on their behalf in matters relating to the design, construction and equipment of vessels in accordance with the provisions of the Convention; and (c) a sufficient number of specimens of their certificates issued under the provisions of the Convention. (2). The Organization shall notify all Parties of the receipt of any communication under paragraph (1)(a) and shall circulate to them any information communicated to it under paragraphs (1)(b) and (c). (1). Each Party shall arrange for an investigation of any casualty occurring to any of its vessels subject to the provisions of the Convention, when it judges that such an investigation may assist in determining what changes in the Convention might be desirable. (2). Each Party shall supply the Organization with pertinent information concerning the findings of such investigation for circulation to all Parties. No reports or recommendations of the Organization based upon such information shall disclose the identity or nationality of the vessels concerned, or in any manner fix or imply responsibility upon any vessel or person. Nothing in this Convention shall prejudice the codification and development of the law of the sea by the United Nations Conference on the Law of the Sea convened pursuant to Resolution 2750 (XXV) of the General Assembly of the United Nations nor the present or future claims and legal views of any State concerning the law of the sea and the nature and extent of coastal and flag State jurisdiction. (1). The Convention shall remain open for signature at the Headquarters of the Organization from 1 October 1977 until 30 June 1978 and shall thereafter remain open for accession. All States may become Parties to the Convention by: (a) signature without reservation as to ratification, acceptance or approval; or (b) signature subject to ratification, acceptance or approval, followed by ratification, acceptance or approval; or (c) accession. (2). Ratification, acceptance, approval or accession shall be effected by the deposit of an instrument to that effect with the Secretary-General. (3). The Secretary-General shall inform all States which have signed the Convention or acceded to it of any signature or of the deposit of any new instrument of ratification, acceptance, approval or accession and the date of its deposit. (1). The Convention shall enter into force twelve months after the date on which not less than fifteen States have either signed it without reservation as to ratification, acceptance, or approval or have deposited the requisite instruments of ratification, acceptance, approval or accession in accordance with Article 9, the aggregate of whose fleets of fishing vessels constitutes not less than 50 per cent by number of the world's fleet of fishing vessels of 24 metres in length and over. (2). The Organization shall inform the States which have signed the Convention or acceded to it of the date on which it enters into force. (3). For States which have deposited an instrument of ratification, acceptance, approval or accession in respect of the Convention after the requirements for entry into force thereof have been met but prior to the date of entry into force, the ratification, acceptance, approval or accession shall take effect on the date of entry into force of the Convention or three months after the date of deposit of the instrument, whichever is the later date. (4). For States which have deposited an instrument of ratification, acceptance, approval or accession after the date on which the Convention entered into force, the Convention shall become effective three months after the date of deposit of the instrument. (5). After the date on which all the conditions required under Article 11 to bring an amendment to the Convention into force have been fulfilled, any instrument of ratification, acceptance, approval or accession deposited shall apply to the Convention as amended. (1). The Convention may be amended by either of the procedures specified in this Article. (2). Amendments after consideration within the Organization: (a) Any amendment proposed by a Party shall be submitted to the Secretary-General, who shall then circulate it to all Members of the Organization and to all the Parties at least six months prior to its consideration. (b) Any amendment proposed and circulated as above shall be referred to the Maritime Safety Committee of the Organization for consideration. (c) Parties whether or not Members of the Organization, shall be entitled to participate in the proceedings of the Maritime Safety Committee for the consideration and adoption of amendments. (d) Amendments shall be adopted by a two-thirds majority of the Parties present and voting in the Maritime Safety Committee expanded as provided for in sub-paragraph (c) (hereinafter referred to as “the expanded Maritime Safety Committee”) on condition that at least one-third of the Parties shall be present at the time of voting. (e) Amendments adopted in accordance with sub-paragraph (d) shall be communicated by the Secretary-General to all the Parties. (f) (i) An amendment to an Article or to Regulations 1 and 3 to 11 shall be deemed to have been accepted on the date on which it is accepted by two-thirds of the Parties, (ii) An amendment to the Annex other than to Regulation 1 and 3 to 11 shall be deemed to have been accepted: (aa) at the end of two years from the date on which it is communicated to the Parties for acceptance; or (bb) at the end of a different period, which shall not be less than one year, if so determined at the time of its adoption by a two-thirds majority of the Parties present and voting in the expanded Maritime Safety Committee. However, if within the specified period either more than one-third of the Parties, or Parties the aggregate of whose fleets of fishing vessels constitutes not less than 50 per cent by number of the fleet of fishing vessels of all the Parties of 24 metres in length and over, notify the Secretary-General that they object to the amendment, it shall be deemed not to have been accepted. (iii) An amendment to an Appendix to the Annex shall be deemed to have been accepted at the end of a period to be determined by the expanded Maritime Safety Committee at the time of its adoption, which period shall be not less than ten months, unless within that period an objection is communicated to the Organization by not less than one-third of the Parties, or Parties the aggregate of whose fleets of fishing vessels constitutes not less than 50 per cent by number of the fleet of fishing vessels of all the Parties of 24 metres in length and over. (g) (i) An amendment to an Article or to Regulations 1 and 3 to 11 shall enter into force with respect to those Parties which have accepted it, six months after the date on which it is deemed to have been accepted, and with respect to each Party which accepts it after that date, six months after the date of that Party's acceptance. (ii) An amendment to the Annex other than to Regulations 1 and 3 to 11 and to an Appendix to the Annex shall enter into force with respect to all Parties, except those which have objected to the amendment under sub-paragraphs (f)(ii) and (iii) and which have not withdrawn such objections, six months after the date on which it is deemed to have been accepted. However, before the date set for entry into force any Party may give notice to the Secretary-General that it exempts itself from giving effect to that amendment for a period not longer than one year from the date of its entry into force, or for such longer period as may be determined by a two-thirds majority of the Parties present and voting in the expanded Maritime Safety Committee at the time of the adoption of the amendment. (3). Amendment by a Conference: (a) Upon the request of a Party concurred in by at least one-third of the Parties, the Organization shall convene a Conference of the Parties to consider amendments to the Convention. (b) Every amendment adopted by such a Conference by a two-thirds majority of the Parties present and voting shall be communicated by the Secretary-General to all the Parties for acceptance. (c) Unless the Conference decides otherwise, the amendment shall be deemed to have been accepted and shall enter into force in accordance with the procedures specified in paragraph (2)(f) and (g) respectively, provided that references in those sub-paragraphs to the expanded Maritime Safety Committee shall be taken to mean references to the Conference. (4). Any Party which has declined to accept the amendment to the Annex shall be deemed not to be a Party for the purpose of application of that amendment. (5). Unless expressly provided otherwise, any amendment to the Convention which relates to the structure of a vessel, shall apply only to vessels for which, on or after the date of entry into force of the amendment: (a) the keel is laid; or (b) construction identifiable with a specific vessel begins; or (c) assembly has commenced comprising at least 50 tonnes or 1 per cent of the estimated mass of all structural material; whichever is the less. (6). Any declaration of acceptance of, or objection to, an amendment or any notice given under paragraph (2)(g)(ii) shall be submitted in writing to the Secretary-General who shall inform all the Parties of any such submission and of the date of its receipt. (7). The Secretary-General shall inform all the Parties of any amendments which enter into force, together with the date on which each such amendment enters into force. (1). The Convention may be denounced by any Party at any time after the expiry of five years from the date on which the Convention enters into force for that Party. (2). Denunciation shall be effected by notification in writing to the Secretary-General who shall inform all other Parties of any such notification received and of the date of its receipt as well as the date on which such denunciation takes effect. (3). A denunciation shall take effect twelve months after receipt of the notification of denunciation by the Secretary-General or after the expiry of any longer period which may be indicated in the notification. (1). The Convention shall be deposited with the Secretary-General who shall transmit certified true copies thereof to all the States which have signed the Convention or acceded to it. (2). As soon as the Convention enters into force, the text shall be transmitted by the Secretary-General to the Secretary-General of the United Nations for registration and publication, in accordance with Article 102 of the Charter of the United Nations. The Convention is established in a single copy in the English, French, Russian and Spanish languages, each text being equally authentic. Official translations in the Arabic, German and Italian languages shall be prepared and deposited with the signed original. CHAPTER II - CONSTRUCTION, WATERTIGHT INTEGRITY AND EQUIPMENT (1) All access openings in bulkheads of enclosed superstructures and other outer structures through which water could enter and endanger the vessel, shall be fitted with doors permanently attached to the bulkhead, framed and stiffened so that the whole structure is of equivalent strength to the unpierced structure, and weathertight when closed. The means for securing these doors weathertight shall consist of gaskets and clamping devices or other equivalent means and shall be permanently attached to the bulkhead or to the doors themselves, and shall be so arranged that they can be operated from each side of the bulkhead. (2) The height above deck of sills in those doorways, in companionways, erections and machinery casings which give direct access to parts of the deck exposed to the weather and sea shall be at least 600 milimetres on the working deck and at least 300 millimetres on the superstructure deck. Where operating experience has shown justification and on approval of the Administration, these heigths, except in the doorways giving direct access to machinery spaces, may be reduced to not less than 380 millimetres and 150 millimetres respectively. (1) The height above deck of hatchway coamings shall be at least 600 millimetres on exposed parts of the working deck and at least 300 millimetres on the superstructure deck. (2) The finished thickness of wood hatchway covers shall include an allowance for abrasion due to rough handling. In any case, the finished thickness of these covers shall be at least 4 millimetres for each 100 millimetres of unsupported span subject to a minimum of 40 millimetres and the width of their bearing surfaces shall be at least 65 millimetres. (3) Arrangements for securing wood hatchway covers weathertight shall be provided to the satisfaction of the Administration. (1) The height above deck of hatchway coamings shall be as specified in Regulation 16(1). Where operating experience has shown justification and on the approval of the Administration the height of these coamings may be reduced, or the coamings omitted entirely, provided that the safety of vessels is not thereby impaired. In this case the hatchway openings shall be kept as small as practicable and the covers be permanently attached by hinges or equivalent means and be capable of being rapidly closed and battened down. (2) For the purpose of strength calculations, it shall be assumed that hatchway covers are subjected to the weight of cargo intended to be carried on them or to the following static loads, whichever is the greater: (a) 10.0 kilonewtons per square metre for vessels of 24 metres in length; (b) 17.0 kilonewtons per square metre for vessels of 100 metres in length and over. For intermediate lengths the load values shall be determined by linear interpolation. The Administration may reduce the loads to not less than 75 per cent of the above values for covers to hatchways situated on the superstructure deck in a position abaft a point located 0.25L from the forward perpendicular. (3) Where covers are made of mild steel, the maximum stress calculated according to paragraph (2) multiplied by 4.25 shall not exceed the minimum ultimate strength of the material. Under these loads the deflections shall not be more than 0.0028 times the span. (4) Covers made of materials other than mild steel shall be at least of equivalent strength to those made of mild steel, and their construction shall be of sufficient stiffness ensuring weathertightness under the loads specified in paragraph (2). (5) Covers shall be fitted with clamping devices and gaskets sufficient to ensure weathertightness, or other equivalent arrangements to the satisfaction of the Administration. (1) Machinery space openings shall be framed and enclosed by casings of a strength equivalent to the adjacent superstructure. External access openings therein shall be fitted with doors complying with the requirements of Regulation 15. (2) Openings other than access openings shall be fitted with covers of equivalent strength to the unpierced structure, permanently attached thereto and capable of being closed weathertight. (1) Where it is essential for fishing operations, flush deck scuttles of the screw, bayonet or equivalent type and manholes may be fitted provided these are capable of being closed watertight and such devices shall be permanently attached to the adjacent structure. Having regard to the size and disposition of the openings and the design of the closing devices, metal-to-metal closures may be fitted if the Administration is satisfied that they are effectively watertight. (2) Openings other than hatchways, machinery space openings, manholes and flush scuttles in the working or superstructure deck shall be protected by enclosed structures fitted with weathertight doors or their equivalent. Companionways shall be situated as close as practicable to the centreline of the vessel. (1) In vessels of 45 metres in length and over, the height above deck of ventilator coamings, other than machinery space ventilator coamings, shall be at least 900 millimetres on the working deck and at least 760 millimetres on the superstructure deck. In vessels of less than 45 metres in length, the height of these coamings shall be 760 milimetres and 450 millimetres respectively. The height above deck of machinery space ventilator openings shall be to the satisfaction of the Administration. (2) Coamings of ventilators shall be of equivalent strength to the adjacent structure and capable of being closed weathertight by closing appliances permanently attached to the ventilator or adjacent structure. Where the coaming of any ventilator exceeds 900 millimetres in height it shall be specially supported. (3) Closing appliances in vessels of 45 metres in length and over need not be fitted to ventilators the coamings of which extend to more than 4.5 metres above the working deck or more than 2.3 metres above the superstructure deck unless specifically required by the Administration. In vessels of less than 45 metres in length, closing appliances need not be fitted to ventilators the coamings of which extend to more than 3.4 metres above the working deck or more than 1.7 metres above the superstructure deck. If the Administration is satisfied that it is unlikely that water will enter the vessel through machinery space ventilators, closing appliances to such ventilators may be omitted. (1) Where air pipes to tanks and void spaces below deck extend above the working or the superstructure decks, the exposed parts of the pipes shall be of strength equivalent to the adjacent structures and fitted with appropriate protection. Openings of air pipes shall be provided with means of closing, permanently attached to the pipe or adjacent structure. (2) The height of air pipes above deck to the point where water may have access below shall be at least 760 millimetres on the working deck and at least 450 millimetres on the superstructure deck. The Administration may accept reduction of the height of an air pipe to avoid interference with the fishing operations. (1) Sounding devices, to the satisfaction of the Administration, shall be fitted: (a) to the bilges of those compartments which are not readily accessible at all times during the voyage; and (b) to all tanks and cofferdams. (2) Where sounding pipes are fitted, their upper ends shall be extended to a readily accessible position and, where practicable, above the working deck. Their openings shall be provided with permanently attached means of closing. Sounding pipes which are not extended above the working deck shall be fitted with automatic self-closing devices. (1) Sidescuttles to spaces below the working deck and to spaces within the enclosed structures on that deck shall be fitted with hinged deadlights capable of being closed watertight. (2) No sidescuttle shall be fitted in such a position that its sill is less than 500 millimetres above the deepest operating waterline. (3) Sidescuttles, together with their glasses and deadlights, shall be of an approved construction. (4) Toughened safety glass or its equivalent shall be used for the wheelhouse windows. (5) The Administration may accept sidescuttles and windows without deadlights in side and aft bulkheads of deckhouses located on or above the working deck if satisfied that the safety of the vessel will not be impaired. (1) Discharges led through the shell either from spaces below the working deck or from within enclosed superstructures or deckhouses on the working deck fitted with doors complying with the requirements of Regulation 15 shall be fitted with accessible means for preventing water from passing inboard. Normally each separate discharge shall have an automatic non-return valve with a positive means of closing it from an accessible position. Such a valve is not required if the Administration considers that the entry of water into the vessel through the opening is not likely to lead to dangerous flooding and that the thickness of the piping is sufficient. The means for operating the positive action valve shall be provided with an indicator showing whether the valve is open or closed. (2) In manned machinery spaces main and auxiliary sea inlets and discharges essential for the operation of machinery may be controlled locally. The controls shall be accessible and shall be provided with indicators showing whether the valves are open or closed. (3) Fittings attached to the shell and the valves required by this Regulation shall be of steel, bronze or other approved ductile material. All pipes between the shell and the valves shall be of steel, except that in spaces other than machinery spaces of vessels constructed of material other than steel the Administration may approve the use of other materials. (1) Where bulwarks on weather parts of the working deck form wells, the minimum freeing port area (A) in square metres, on each side of the vessel for each well on the working deck shall be determined in relation to the length (ℓ) and height of bulwark in the well as follows: (a) A = 0.07ℓ (ℓ need not be taken as greater than 0.7 L). (b) (i) Where the bulwark is more than 1 200 millimetres in average height the required area shall be increased by 0.004 square metres per metre of length of well for each 100 millimetres difference in height. (ii) Where the bulwark is less than 900 millimetres in average height, the required area may be decreased by 0.004 square metres per metre of length of well for each 100 millimetres difference in height. (2) The freeing port area calculated according to paragraph (1) shall be increased where the Administration considers that the vessel's sheer is not sufficient to ensure that the deck is rapidly and effectively freed of water. (3) Subject to the approval of the Administration the minimum freeing port area for each well on the superstructure deck shall be not less than one-half the area (A) given in paragraph (1). (4) Freeing ports shall be so arranged along the length of bulwarks as to ensure that the deck is freed of water most rapidly and effectively. Lower edges of freeing ports shall be as near the deck as practicable. (5) Poundboards and means for stowage of the fishing gear shall be arranged so that the effectiveness of freeing ports will not be impaired. Poundboards shall be so constructed that they can be locked in position when in use and shall not hamper the discharge of shipped water. (6) Freeing ports over 300 millimetres in depth shall be fitted with bars spaced not more than 230 millimetres nor less than 150 millimetres apart or provided with other suitable protective arrangements. Freeing port covers, if fitted, shall be of approved construction. If devices are considered necessary for locking freeing port covers during fishing operations they shall be to the satisfaction of the Administration and easily operable from a readily accessible position. (7) In vessels intended to operate in areas subject to icing, covers and protective arrangements for freeing ports shall be capable of being easily removed to restrict ice accretion. The size of openings and means provided for removal of these protective arrangements shall be to the satisfaction of the Administration. Anchor equipment designed for quick and safe operation shall be provided which shall consist of anchoring equipment, anchor chains or wire ropes, stoppers and a windlass or other arrangements for dropping and hoisting the anchor and for holding the vessel at anchor in all foreseeable service conditions. Vessels shall also be provided with adequate mooring equipment for safe mooring in all operating conditions. Anchor and mooring equipment shall be to the satisfaction of the Administration. CHAPTER III - STABILITY AND ASSOCIATED SEAWORTHINESS Vessels shall be so designed and constructed that the requirements of this Chapter will be satisfied in the operating conditions referred to in Regulation 33. Calculations of the righting lever curves shall be to the satisfaction of the Administration. (1) The following minimum stability criteria shall be met unless the Administration is satisfied that operating experience justifies departures therefrom: (a) the area under the righting lever curve (GZ curve) shall not be less than 0.055 metre-radians up to 30 degrees angle of heel and not less than 0.090 metre-radians up to 40 degrees or the angle of flooding θf if this angle is less than 40 degrees. Additionally, the area under the righting lever curve (GZ curve) between the angles of heel of 30 degrees and 40 degrees or between 30 degrees and θf, if this angle is less than 40 degrees shall not be less than 0.030 metre-radians. θf is the angle of heel at which openings in the hull, superstructure or deckhouse which cannot rapidly be closed watertight commence to immerse. In applying this criterion, small openings through which progressive flooding cannot take place need not be considered as open; (b) the righting lever GZ shall be at least 200 millimetres at an angle of heel equal to or greater than 30 degrees; (c) the maximum righting lever GZmax shall occur at an angle of heel preferably exceeding 30 degrees but not less than 25 degrees; (d) the initial metacentric height GM shall not be less than 350 millimetres for single deck vessels. In vessels with complete superstructure or vessels of 70 metres in length and over the metacentric height may be reduced to the satisfaction of the Administration but in no case shall be less than 150 millimetres. (2) Where arrangements other than bilge keels are provided to limit the angles of roll, the Administration shall be satisfied that the stability criteria given in paragraph (1) are maintained in all operating conditions. (3) Where ballast is provided to ensure compliance with paragraph (1), its nature and arrangement shall be to the satisfaction of the Administration. The angle of heel at which progressive flooding of fish-holds could occur through hatches which remain open during fishing operations and which cannot rapidly be closed shall be at least 20 degrees unless the stability criteria of Regulation 28(1) can be satisfied with the respective fish-holds partially or completely flooded. Vessels engaged in particular fishing methods where additional external forces are imposed on the vessel during fishing operations, shall meet the stability criteria of Regulation 28(1) increased, if necessary, to the satisfaction of the Administration. Vessels shall be able to withstand, to the satisfaction of the Administration, the effect of severe wind and rolling in associated sea conditions taking account of the seasonal weather conditions, the sea states in which the vessel will operate, the type of vessel and its mode of operation. Vessels shall be able to withstand, to the satisfaction of the Administration, the effect of water on deck, taking account of the seasonal weather conditions, the sea states in which the vessel will operate, the type of vessel and its mode of operation. (1) The number and type of operating conditions to be considered shall be to the satisfaction of the Administration and shall include the following: (a) departure for the fishing grounds with full fuel, stores, ice, fishing gear, etc.; (b) departure from the fishing grounds with full catch; (c) arrival at home port with full catch and 10 per cent stores, fuel, etc.; and (d) arrival at home port with 20 per cent of full catch and 10 per cent stores, fuel, etc. (2) In addition to the specific operating conditions given in paragraph (1) the Administration shall also be satisfied that the minimum stability criteria given in Regulation 28 are met under all other actual operating conditions including, those which produce the lowest values of the stability parameters contained in these criteria. The Administration shall also be satisfied that those special conditions associated with a change in the vessel's mode or areas of operation which affect the stability considerations of this Chapter are taken into account. (3) Concerning the conditions referred to in paragraph (1), the calculations shall include the following: (a) allowance for the weight of the wet fishing nets and tackle, etc. on the deck; (b) allowance for ice accretion, if anticipated, in accordance with the provisions of Regulation 34; (c) homogeneous distribution of the catch, unless this is inconsistent with practice; (d) catch on deck, if anticipated, in operating conditions referred to in paragraph (1)(b) and (c) and paragraph (2); (e) waterballast if carried either in tanks which are especially provided for this purpose or in other tanks also equipped for carrying water ballast; and (f) allowance for the free surface effect of liquids and, if applicable, catch carried. (1) For vessels operating in areas where ice accretion is likely to occur the following icing allowance shall be made in the stability calculations: (a) 30 kilogrammes per square metre on exposed weather decks and gangways; (b) 7.5 kilogrammes per square metre for projected lateral area of each side of the vessel above the water plane; (c) the projected lateral area of discontinuous surfaces of rail, spars (except masts) and rigging of vessels having no sails and the projected lateral area of other small objects shall be computed by increasing the total projected area of continuous surfaces by 5 per cent and the static moments of this area by 10 per cent. (2) Vessels intended for operation in areas where ice accretion is known to occur shall be: (a) designed to minimize the accretion of ice; and (b) equipped with such means for removing ice as the Administration may require. (1) Every vessel shall undergo an inclining test upon its completion and the actual displacement and position of the centre of gravity shall be determined for the light ship condition. (2) Where alterations are made to a vessel affecting its light ship condition and the position of the centre of gravity, the vessel shall, if the Administration considers this necessary, be re-inclined and the stability information revised. (3) The Administration may allow the inclining test of an individual vessel to be dispensed with provided basic stability data are available from the inclining test of a sister ship and it is shown to the satisfaction of the Administration that reliable stability information for the exempted vessel can be obtained from such basic data. (1) Suitable stability information shall be supplied to enable the skipper to assess with ease and certainty the stability of the vessel under various operating conditions. Such information shall include specific instructions to the skipper warning him of those operating conditions which could adversely affect either the stability or the trim of the vessel. A copy of the stability information shall be submitted to the Administration for approval. (2) The approved stability information shall be kept on board, readily accessible at all times and inspected at the periodical surveys of the vessel to ensure that is has been approved for the actual operating conditions. (3) Where alterations are made to a vessel affecting its stability revised stability calculations shall be prepared and submitted to the Administration for approval. If the Administration decides that the stability information must be revised, the new information shall be supplied to the skipper and the superseded information removed. The catch shall be properly secured against shifting which could cause dangerous trim or heel of the vessel. The scantlings of portable fish-hold divisions, if fitted, shall be to the satisfaction of the Administration. The bow height shall be sufficient, to the satisfaction of the Administration, to prevent the excessive shipping of water and shall be determined taking account of the seasonal weather conditions, the sea states in which the vessel will operate, the type of vessel and its mode of operation. A maximum permissible operating draught shall be approved by the Administration and shall be such that, in the associated operating condition, the stability criteria of this Chapter and the requirements of Chapters II and VI as appropriate are satisfied. Vessels of 100 metres in length and over, where the total number of persons carried is 100 or more, shall be capable, to the satisfaction of the Administration, of remaining afloat with positive stability, after the flooding of any one compartment assumed damaged, having regard to the type of vessel, the intended service and area of operation. CHAPTER IV - MACHINERY AND ELECTRICAL INSTALLATIONS AND PERIODICALLY UNATTENDED MACHINERY SPACES – PART A - GENERAL Machinery installations (1) Main propulsion, control, steam pipe, fuel oil, compressed air, electrical and refrigeration systems; auxiliary machinery; boilers and other pressure vessels; piping and pumping arrangements; steering equipment and gears, shafts and couplings for power transmission shall be designed, constructed, tested, installed and serviced to the satisfaction of the Administration. This machinery and equipment, as well as lifting gear, winches, fish handling and fish processing equipment shall be protected so as to reduce to a minimum any danger to persons on board. Special attention shall be paid to moving parts, hot surfaces and other dangers. (2) Machinery spaces shall be so designed as to provide safe and free access to all machinery and its controls as well as to any other parts which may require servicing. Such spaces shall be adequately ventilated. (3) (a) Means shall be provided whereby the operational capability of the propulsion machinery can be sustained or restored even though one of the essential auxiliaries becomes inoperative. Special consideration shall be given to the functioning of: (i) the arrangements which supply fuel oil pressure for main propulsion machinery; (ii) the normal sources of lubricating oil pressure; (iii) the hydraulic, pneumatic and electrical means for the control of main propulsion machinery including controllable pitch propellers; (iv) the sources of water pressure for main propulsion cooling systems; and (v) an air compressor and an air receiver for starting or control purposes; provided that the Administration may, having regard to overall safety considerations, accept a partial reduction in capability in lieu of full normal operation. (b) Means shall be provided whereby the machinery can be brought into operation from the dead ship condition without external aid. (4) Main propulsion machinery and all auxiliary machinery essential to the propulsion and the safety of the vessel shall, as fitted, be capable of operating whether the vessel is upright or listed up to 15 degrees either way under static conditions and up to 22½ degrees either way under dynamic conditions, i.e. when rolling either way and simultaneously pitching (inclined dynamically) up to 7½ degrees by bow or stern. The Administration may permit deviation from these angles, taking into consideration the type, size and service conditions of the vessel. (5) Special consideration shall be given to the design, construction and installation of propulsion machinery systems so that any mode of their vibrations shall not cause undue stresses in such machinery systems in the normal operating ranges. Electrical installations (6) The design and construction of electrical installations shall be such as to provide: (a) the services necessary to maintain the vessel in normal operational and habitable conditions without having recourse to an emergency source of power; (b) the services essential to safety when failure of the main source of electrical power occurs; and (c) protection of the crew and vessel from electrical hazards. (7) The Administration shall be satisfied that Regulations 54 to 56 are uniformly implemented and applied. Periodically unattended machinery spaces (8) Regulations 57 to 62 shall apply, in addition to Regulations 41 to 56 and 63 to 105, to vessels with periodically unattended machinery spaces. (9) Measures shall be taken to the satisfaction of the Administration to ensure that all equipment is functioning in a reliable manner in all operating conditions, including manoeuvring, and that arrangements to the satisfaction of the Administration are made for regular inspections and routine tests to ensure continuous reliable operation. (10) Vessels shall be provided with documentary evidence to the satisfaction of the Administration of their fitness to operate with periodically unattended machinery spaces. CHAPTER IV - MACHINERY AND ELECTRICAL INSTALLATIONS AND PERIODICALLY UNATTENDED MACHINERY SPACES – PART B - MACHINERY INSTALLATIONS (See also Regulation 41) (1) Main and auxiliary machinery essential for the propulsion and safety of the vessel shall be provided with effective means of control. (2) Internal combustion engines of a cylinder diameter greater than 200 millimetres or a crankcase volume greater than 0.6 cubic metres shall be provided with crankcase explosion relief valves of an approved type with sufficient relief area. (3) Where main or auxiliary machinery including pressure vessels or any parts of such machinery are subject to internal pressure and may be subject to dangerous overpressure, means shall be provided, where applicable, which will protect against such excessive pressure. (4) All gearing and every shaft and coupling used for transmission of power to machinery essential for the propulsion and safety of the vessel or the safety of persons on board shall be so designed and constructed that it will withstand the maximum working stresses to which it may be subjected in all service conditions. Due consideration shall be given to the type of engines by which it is driven or of which it forms part. (5) Main propulsion machinery and, where applicable, auxiliary machinery shall be provided with automatic shut-off arrangements in the case of failures, such as lubricating oil supply failure, which could lead rapidly to damage, complete breakdown or explosion. An advance alarm shall also be provided so that warning is given before automatic shut-off but the Administration may permit provisions for overriding automatic shut-off devices. The Administration may also exempt vessels from the provisions of this paragraph, giving consideration to the type of vessel or its specific service. (1) Vessels shall have sufficient power for going astern to secure proper control of the vessel in all normal circumstances. (2) The ability of the machinery to reverse the direction of thrust of the propeller in sufficient time and so to bring the vessel to rest within a reasonable distance from maximum ahead service speed shall be demonstrated at sea. (1) Every steam boiler and every unfired steam generator shall be provided with not less than two safety valves of adequate capacity. Provided that the Administration may, having regard to the output or any other features of any steam boiler or unfired steam generator, permit only one safety valve to be fitted if satisfied that adequate protection against overpressure is thereby provided. (2) Every oil fired steam boiler which is intended to operate without manual supervision shall have safety arrangements which shut off the fuel supply and give an alarm in the case of low water level, air supply failure or flame failure. (3) The Administration shall give special consideration to steam boiler installations to ensure that feed systems, monitoring devices, and safety provisions are adequate in all respects to ensure the safety of boilers, steam pressure vessels and steam piping arrangements. Two separate means of communication between the wheelhouse and the machinery space control platform shall be provided. One of the means shall be an engine room telegraph except that in vessels of less than 45 metres in length, where the propulsion machinery is directly controlled from the wheelhouse, the Administration may accept means of communication other than an engine room telegraph. (1) Where remote control of propulsion machinery is provided from the wheelhouse, the following shall apply: (a) under all operating conditions, including manoeuvring, the speed, direction of thrust and, if applicable, the pitch of the propeller shall be fully controllable from the wheelhouse; (b) the remote control referred to in sub-paragraph (a) shall be performed by means of a control device to the satisfaction of the Administration with, where necessary, means of preventing overload of the propulsion machinery; (c) the main propulsion machinery shall be provided with an emergency stopping device in the wheelhouse and independent from the wheelhouse control system referred to in sub-paragraph (a); (d) remote control of the propulsion machinery shall be possible only from one station at a time; at any control station interlocked control units may be permitted. There shall be at each station an indicator showing which station is in control of the propulsion machinery. The transfer of control between the wheelhouse and machinery spaces shall be possible only in the machinery space or control room. On vessels of less than 45 metres in length the Administration may permit the control station in the machinery space to be an emergency station only, provided that the monitoring and control in the wheelhouse is adequate; (e) indicators shall be fitted in the wheelhouse for: (i) propeller speed and direction in the case of fixed propellers; (ii) propeller speed and pitch position in the case of controllable pitch propellers; and (iii) advance alarm as required in Regulation 42(5); (f) it shall be possible to control the propulsion machinery locally, even in the case of failure in any part of the remote control system; (g) unless the Administration considers it impracticable the design of the remote control system shall be such that if it fails an alarm will be given and the pre-set speed and direction of thrust will be maintained until local control is in operation; (h) special arrangements shall be provided to ensure that automatic starting shall not exhaust the starting possibilities. An alarm shall be provided to indicate low starting air pressure and shall be set at a level which will still permit main engine starting operations. (2) Where the main propulsion and associated machinery including sources of main electrical supply are provided with various degrees of automatic or remote control and are under continuous manned supervision from a control room, the control room shall be so designed, equipped and installed that the machinery operation will be as safe and effective as if it were under direct supervision. (3) In general, automatic starting, operational and control systems shall include means for manually overriding the automatic means, even in the case of failure of any part of the automatic and remote control system. (1) Means shall be provided to prevent excess pressure in any part of compressed air systems and wherever water-jackets or casings of air compressors and coolers might be subjected to dangerous excess pressure due to leakage into them from air pressure parts. Suitable pressure-relief arrangements shall be provided. (2) The main starting air arrangements for main propulsion internal combustion engines shall be adequately protected against the effects of backfiring and internal explosion in the starting air pipes. (3) All discharge pipes from starting air compressors shall lead directly to the starting air receivers and all starting pipes from the air receivers to main or auxiliary engines shall be entirely separate from the compressor discharge pipe system. (4) Provision shall be made to reduce to a minimum the entry of oil into the air pressure systems and to drain these systems. (1) Fuel oil which has a flashpoint of less than 60 degrees celsius (closed cup test) as determined by an approved flashpoint apparatus shall not be used as fuel, except in emergency generators, in which case the flashpoint shall be not less than 43 degrees celsius. Provided that the Administration may permit the general use of fuel oil having a flashpoint of not less than 43 degrees celsius subject to such additional precautions as it may consider necessary and on condition that the temperature of the space in which such fuel is stored or used shall not rise to within 10 degrees celsius below the flashpoint of the fuel. (2) Safe and efficient means of ascertaining the amount of fuel oil contained in any oil tank shall be provided. If sounding pipes are installed, their upper ends shall terminate in safe positions and shall be fitted with suitable means of closure. Tubular gauge glasses shall not be fitted, but suitably protected gauges having flat glasses of substantial thickness and self-closing fittings may be used. Other means of ascertaining the amount of fuel oil contained in any fuel oil tank may be permitted providing their failure or overfilling of the tanks will not permit release of fuel. (3) Provision shall be made to prevent overpressure in any oil tank or in any part of the fuel oil system including the filling pipes. Relief valves and air or overflow pipes shall discharge to a position and in a manner which is safe. (4) Subject to the satisfaction of the Administration, fuel oil pipes which, if damaged, would allow oil to escape from a storage, settling or daily service tank situated above the double bottom, shall be fitted with a cock or valve on the tank capable of being closed from a safe position outside the space concerned in the event of a fire arising in the space in which such tanks are situated. In the special case of deep tanks situated in any shaft or pipe tunnel or similar space, valves on the tank shall be fitted but control in the event of fire may be effected by means of an additional valve on the pipe or pipes outside the tunnel or similar space. If such additional valve is fitted in the machinery space it shall be capable of being operated outside this space. (5) Pumps forming part of the fuel oil system shall be separate from any other system and the connexions of any such pumps shall be provided with an efficient relief valve which shall be in closed circuit. Where fuel oil tanks are alternatively used as liquid ballast tanks, proper means shall be provided to isolate the fuel oil and ballast systems. (6) No oil tank shall be situated where spillage or leakage therefrom can constitute a hazard by falling on heated surfaces. Precautions shall be taken to prevent any oil that may escape under pressure from any pump, filter or heater from coming into contact with heated surfaces. (7) (a) Fuel oil pipes and their valves and fittings shall be of steel or other equivalent material, provided that restricted use of flexible pipes may be permitted in positions where the Administration is satisfied that they are necessary. Such flexible pipes and end attachments shall be of adequate strength and shall, to the satisfaction of the Administration, be constructed of approved fire resistant materials or have fire-resistant coatings. (b) Where necessary, fuel oil and lubricating oil pipelines shall be screened or otherwise suitably protected to avoid, as far as practicable, oil spray or oil leakage on heated surfaces or into machinery air intakes. The number of joints in piping systems shall be kept to a minimum. (8) As far as practicable, fuel oil tanks shall be part of the vessel's structure and shall be located outside machinery spaces of Category A. Where fuel oil tanks, other than double bottom tanks, are necessarily located adjacent to or within machinery spaces of Category A, at least one of their vertical sides shall be contiguous to the machinery space boundaries, and shall preferably have a common boundary with the double bottom tanks where fitted and the area of the tank boundary common with the machinery space shall be kept to a minimum. When such tanks are sited within the boundaries of machinery spaces of Category A they shall not contain fuel oil having a flashpoint of less than 60 degrees celsius (closed cup test). In general, the use of free-standing fuel oil tanks shall be avoided in fire hazard areas, and particularly in machinery spaces of Category A. When free-standing fuel oil tanks are permitted, they shall be placed in an oil-tight spill tray of ample size having a suitable drain pipe leading to a suitably sized spill oil tank. (9) The ventilation of machinery spaces shall be sufficient under all normal conditions to prevent accumulation of oil vapour. (10) The arrangements for the storage, distribution and use of oil employed in pressure lubrication systems shall be to the satisfaction of the Administration. Such arrangements in machinery spaces of Category A and, wherever practicable, in other machinery spaces shall at least comply with the provisions of paragraphs (1), (3), (6) and (7) and in so far as the Administration may consider necessary with paragraphs (2) and (4). This does not preclude the use of sight flow glasses in lubrication systems provided they are shown by test to have a suitable degree of fire resistance. (11) The arrangements for the storage, distribution and use of flammable oils employed under pressure in power transmission systems other than oils referred to in paragraph (10) in control and activating systems and heating systems shall be to the satisfaction of the Administration. In locations where means of ignition are present such arrangements shall at least comply with the provisions of paragraphs (2) and (6) and with the provisions of paragraphs (3) and (7) in respect of strength and construction. (1) An efficient bilge pumping plant shall be provided which under all practical conditions shall be capable of pumping from and draining any watertight compartment which is neither a permanent oil tank nor a permanent water tank whether the vessel is upright or listed. Wing suctions shall be provided if necessary for that purpose. Arrangements shall be provided for easy flow of water to the suction pipes. Provided the Administration is satisfied that the safety of the vessel is not impaired the bilge pumping arrangements may be dispensed with in particular compartments. (2) (a) At least two independently driven power bilge pumps shall be provided, one of which may be driven by the main engine. A ballast pump or other general service pump of sufficient capacity may be used as a power driven bilge pump. (b) Power bilge pumps shall be capable of giving a speed of water of at least 2 metres per second through the main bilge pipe which shall have an internal diameter of at least: where: d is the internal diameter in millimetres, and L, B and D are in metres. (c) Each of the bilge pumps provided in accordance with this Regulation shall be provided with a direct bilge suction, one of these suctions drawing from the port side of the machinery space and the other from the starboard side, except that in the case of a vessel of less than 75 metres in length only one bilge pump need be provided with a direct bilge suction. (d) No bilge suction shall have an inside diameter of less than 50 millimetres. The arrangement and sizing of the bilge system shall be such that the full rated capacity of the pump specified above can be applied to each of the watertight compartments located between the collision and afterpeak bulkheads. (3) A bilge ejector in combination with an independently driven high pressure sea-water pump may be installed as a substitute for one independently driven bilge pump required by paragraph (2)(a), provided this arrangement is to the satisfaction of the Administration. (4) In vessels where fish handling or processing may cause quantities of water to accumulate in enclosed spaces, adequate drainage shall be provided. (5) Bilge pipes shall not be led through fuel oil, ballast or double bottom tanks, unless these pipes are of heavy gauge steel construction. (6) Bilge and ballast pumping systems shall be arranged so as to prevent water passing from the sea or from water ballast spaces into holds or into machinery spaces or from one watertight compartment to another. The bilge connexion to any pump which draws from the sea or from water ballast spaces shall be fitted with either a non-return valve or a cock which cannot be opened simultaneously either to the bilges and to the sea or to the bilges and water ballast spaces. Valves in bilge distribution boxes shall be of a non-return type. (7) Any bilge pipe piercing a collision bulkhead shall be fitted with a positive means of closing at the bulkhead with remote control from the working deck with an indicator showing the position of the valve provided that, if the valve is fitted on the after side of the bulkhead and is readily accessible under all service conditions, the remote control may be dispensed with. Measures shall be taken to reduce the effects of noise upon personnel in machinery spaces to levels satisfactory to the Administration. (1) Vessels shall be provided with a main steering gear and an auxiliary means of actuating the rudder to the satisfaction of the Administration. The main steering gear and the auxiliary means of actuating the rudder shall be arranged so that so far as is reasonable and practicable a single failure in one of them will not render the other one inoperative. (2) Where the main steering gear comprises two or more identical power units an auxiliary steering gear need not be fitted if the main steering gear is capable of operating the rudder as required by paragraph (10) when any one of the units is out of operation. Each of the power units shall be operated from a separate circuit. (3) The position of the rudder, if power operated, shall be indicated in the wheelhouse. The rudder angle indication for power-operated steering gear shall be independent of the steering gear control system. (4) In the event of failure of any of the steering gear units an alarm shall be given in the wheelhouse. (5) Indicators for running indication of the motors of electric and electrohydraulic steering gear shall be installed in the wheelhouse. Short circuit protection, an overload alarm and a no-voltage alarm shall be provided for these circuits and motors. Protection against excess current, if provided, shall be for not less than twice the full load current of the motor or circuit so protected, and shall be arranged to permit the passage of the appropriate starting currents. (6) The main steering gear shall be of adequate strength and sufficient to steer the vessel at maximum service speed. The main steering gear and rudder stock shall be so designed that they will not be damaged at maximum speed astern or by manoeuvring during fishing operations. (7) The main steering gear shall, with the vessel at its maximum permissible operating draught, be capable of putting the rudder over from 35 degrees on one side to 35 degrees on the other side with the vessel running ahead at maximum service speed. The rudder shall be capable of being put over from 35 degrees on either side to 30 degrees on the other side in not more than 28 seconds, under the same conditions. The main steering gear shall be operated by power where necessary to fulfil these requirements. (8) The main steering gear power unit shall be arranged to start either by manual means in the wheelhouse or automatically when power is restored after a power failure. (9) The auxiliary means for actuating the rudder shall be of adequate strength and sufficient to steer the vessel at navigable speed and capable of being brought speedily into action in an emergency. (10) The auxiliary means for actuating the rudder shall be capable of putting the rudder over from 15 degrees on one side to 15 degrees on the other side in not more than 60 seconds with the vessel running at one half of its maximum service speed ahead or 7 knots whichever is the greater. The auxiliary means for actuating the rudder shall be operated by power where necessary to fulfil these requirements. (11) Electric or electrohydraulic steering gear in vessels of 75 metres in length and over shall be served by at least two circuits fed from the main switchboard and these circuits shall be as widely separated as possible. In vessels of 75 metres in length and over an engineers' alarm shall be provided to be operated from the engine control room or at the manoeuvring platform as appropriate, and shall be clearly audible in the engineers' accommodation. (1) Refrigeration systems shall be so designed, constructed, tested and installed as to take account of the safety of the systems considering the degree of possible harm to persons from the refrigerant used and shall be to the satisfaction of the Admi

    The text continues in the official source.

    Related guides, FAQ and contract templates